







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Delta Bathroom Remodeling in Frisco: What to Know First
We provide independent Delta bathroom remodeling in Frisco, and a full Delta bath typically runs $9,000 – $28,000 depending on size, tile selection and whether we’re working around existing plumbing. Most Delta shower and tub projects take one to three weeks from demolition to final caulk, and you get a written price before demolition starts. As an independent Delta service provider, we’re not affiliated with or authorized by Delta, and we don’t pretend otherwise.
This page is for Frisco homeowners who already have Delta fixtures and trim in the bath – a Delta shower valve, a Delta tub filler, a Delta handheld on a slide bar – and want the remodel done around those products rather than ripped out and replaced with whatever’s on a big-box shelf. The Delta name is one of the brands we install and work with; we also handle KraftMaid, Kohler, Cambria and Toto when a project calls for them. Call (833) 954-5757 for a free estimate.
How Delta Products Fail – and How We Fix Them

Delta builds a lot of the plumbing that ends up inside Frisco bathrooms, and like any brand, certain parts show wear sooner than others. Here are the failures we see most, with the fix we’d actually recommend.
- Delta Monitor 1300/1400 series valve cartridges that stick or run lukewarm: The pressure-balance spool inside the cartridge gums up as Frisco’s hard water leaves mineral scale, and the result is a handle you can barely turn or a shower that won’t hold temperature. We rebuild with the correct replacement cartridge rather than swap the whole valve body, which keeps the rough-in in place and the tile intact.
- Delta single-handle kitchen-style cartridge wear in guest baths: On the Delta single-handle bath faucets common in second baths, the ball-and-spring cartridge develops a slow drip that eventually etches the drain. We replace the cartridge, resurface or swap the drain, and check the supply stops while the wall is open.
- Delta shower trim pitting and finish loss: The chrome or brushed-nickel finish on older Delta shower trim pits in bathrooms with heavy steam and no exhaust fan. We recommend a proper exhaust fan with a timer, not a larger trim, since the finish failure is a ventilation problem showing up on the fixture.
- Delta tub-filler and handshower diverter seizure: The diverter on Delta tub fillers stiffens when sediment builds behind it, and forcing the lever cracks the body. We disassemble, clean and reseat the diverter, and replace the o-rings with OEM parts so the seal holds.
- Delta slide-bar and handheld bracket loosening: The set screws on Delta slide bars back out over time, and the handheld drops mid-shower. We re-anchor the bar into solid blocking, not just drywall, so it stays put through years of daily use.
Two details you won’t get from Delta’s own site: first, the pressure-balance spool in a Monitor valve is the part that fails before the cartridge seat does, so a “cartridge replacement” that skips the spool will run lukewarm again within months. Second, Frisco summers push attic and wall-cavity temperatures high enough that older flexible supply lines behind a Delta valve soften and seep – if we open a wall for a valve job and see original braided lines from the 1990s, we flag them.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Our Delta Bathroom Remodeling Process
- 1
Diagnostics and walkthrough. We look at the existing Delta valve, trim and tub, test water pressure and shut-off function, and photograph the rough-in. We tell you which Delta parts are salvageable and which aren’t before any demolition.
- 2
Written price. You get a line-item written price – tile, setting materials, valve rebuild or swap, trim, labor, permits where required – before any work starts. The number on day one is the number on the invoice.
- 3
Parts decision. Where Delta OEM parts make sense, we use them. Where a quality aftermarket equivalent is the better value and won’t void your Delta warranty, we say so and explain why.
- 4
The rebuild. Demo, cement board substrate (the moisture-resistant layer behind your tile), waterproofing, tile, and the Delta valve and trim reinstall, all to the plan you approved.
- 5
Test and inspect. We pressure-test the valve, run the shower through a full hot cycle, check for leaks at every connection, and walk the finished room with you.
- 6
Cleanup and guarantee. The job site is left cleaner than we found it, and the work is covered by our written 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Delta Bathroom Remodeling Costs in Frisco

Here’s what Delta bathroom projects typically run in Frisco. These are real ranges; what drives your number up or down is the size of the room, tile selection, and whether the existing Delta rough-in can stay in place.
| Project | Typical Frisco Range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
A Delta valve rebuild alone runs a few hundred dollars; the jump to five figures is almost always tile work, waterproofing and the size of the shower or tub footprint. Call (833) 954-5757 for an exact quote – estimates are free and always in writing.
Why Frisco Homeowners Call Penhallow Remodeling Frisco for Delta Work
We put the price and the guarantee in writing before a single tile is set. That’s the Kingswell standard, and it’s why Frisco homeowners who’ve been burned by a verbal estimate that ballooned after demo call us instead. Every repair is covered by a written 365-Day Done Right Promise: if it fails inside the guarantee period, we come back and fix it at no charge, and a second visit if a repair fails is free – no service call, no re-inspection fee. Our technicians have up to 22 years of experience, arrive in uniform, and are background-checked, so you know exactly who’s walking into your home. A live person answers the phone any time you call. And when a Delta job needs cabinetry or countertops, we bring in KraftMaid, Kohler, Cambria or Toto so the rest of the room matches the standard of the plumbing. Call (833) 954-5757 to schedule your free estimate.
FAQs

Does remodeling my Frisco bathroom void the Delta warranty on my fixtures? No, as long as the Delta fixtures themselves are installed and serviced correctly; the warranty covers the fixture, not the labor or the surrounding tile work. We follow Delta’s install specs so the manufacturer coverage stays intact, and our own 365-Day Done Right Promise backs the labor.
Can you get Delta parts quickly for a Frisco repair? Yes – OEM Delta cartridges, spools and trim are widely stocked, and most jobs don’t wait on a backorder. If a specific Delta series part needs ordering, we tell you the timeline before we start, not after.
Should I repair or replace my Delta valve during a remodel? Repair if the valve body is sound and only the cartridge and spool are worn; replace if the rough-in is corroded or you want a different function like a thermostatic valve. We open the wall, show you what we see, and give you the written price for both paths.
How long does a Delta shower remodel take in Frisco? A shower-only remodel typically takes one to two weeks; a full bathroom remodel runs two to three. The written schedule is part of the written price.
Do you pull permits for Delta bathroom work? When the scope requires a plumbing or electrical permit in Frisco, yes – permitted and inspected, and that line is in the written price from the start.
Call (833) 954-5757 for a freeestimate and a written number you can hold us to.
Written by the team at Penhallow Remodeling Frisco, serving Frisco and nearby areas.












